A/C Repair Tomball TX | Heating, Plumbing & Electrical Services

Came out today and put the top back on the Faucet in the guest bathroom. Ran it and tested it as much as possible to ensure no leaks and we also moved it as forward as we could so she could get her hands down comfortably in the sink. Customer paid with credit card the service fee and no follow-up needed.

As Per Agreement

Returned to install 2 media cabinets with plenum. Rebuilt flue vent to avoid making contact with secondary return plenum. Checked for proper operations, removed all 1in filters from wall. Showed customer repair. Made sure unit was completely operational before departure.

Final Inspection

Home owner had a leak in wall. Repaired leak. Also wanted a price on installing a ice maker in washer area. Sending bid for ice maker and repaired leak in wall and turned water on to check for leaks. Found none

System- Single Approx Age of System: 1 Refrigerant Type- R410a Metering Device- TXV SP/HP: 109/307 SLT/LLT: 48/83 VSAT/LSAT- 36/97 Superheat/Subcool- 12/13 Outdoor Entering Air Temp- 81 Outdoor Fan FLA- 0.9 Compressor RLA/LRA- 8.4/76.1 Contactor Voltage- 244 Capacitor Rating- 40/5 Indoor Return Dry Bulb Temp- 71 Return Wet Bulb Temp- 58 Supply Temp- 50 Temperature Difference-20 Required Difference- 20 Blower FLA- 4.1 Filter Sizes – 12x12 (2), 12x20 Changed Filters – N Blew out drain line: Y Returned tstat to original settings: Y Unit operational; prior to leaving: Y Notes- performed ac tuneup. System was operational upon arrival. Angel expressed interest in the air scrubber but does not want to do it on this visit. Scheduled next tune up date: 01/14

Customer had us out today for a dripping faucet in the mast bath. Replaced the cartridge in the lav on the right hand side. Turned water on and checked for leaks and functionality, everything is working as it should. Customer also had concerns about water c9ming from the dishwasher air gap. Removed hose from air gap and found a blockage. Cleared the blockag3 and everything is working as it should. No warranty on drain cleaning. We will need to schedule the QAC

System- upstairs Approx Age of System: 15 Refrigerant Type- R22 / Metering Device- Fixed Orifice / SP/HP: 61/175 SLT/LLT: 61/89 VSAT/LSAT- 35/92 Superheat/Subcool- 25/2 Outdoor Entering Air Temp- Outdoor Fan FLA- .7 Compressor RLA/LRA- 6.7 Contactor Voltage- 244 Capacitor Rating- Turbo Indoor Return Dry Bulb Temp - 74 Return Wet Bulb Temp- 66 Supply Temp- 55 Temperature Difference- 19 Required Difference- 15-20 Blower FLA- 3.7 Filter Sizes – 20x25x1 Changed Filters – N customer will Blew out drain line: N no blow out Returned tstat to original settings: Y Unit operational; prior to leaving: Y with issues Notes- Scheduled next tune up date: System- downstairs Approx Age of System: 1 Refrigerant Type- R410a Metering Device- TXV SP/HP:116/303 SLT/LLT: 54/77 VSAT/LSAT- 40/96 Superheat/Subcool- 15/18 Outdoor Entering Air Temp- Outdoor Fan FLA- .3 Compressor RLA/LRA-5.7/62 Contactor Voltage-243 Capacitor Rating- 40/5 Actual 40/5 Indoor

As Per Agreement

Came out today to give an estimate to run a drain line for the customers RV. The customer may end up digging the ditch lines for us to save money but we will need to provide an estimate to drop a pump grinding station and a stub out and run 2 inch line all the way down to the septic tank that is 125 feet away. The customer will be sending us pictures of where the tank is actually located and any other information that you can give us. We will be working on different estimates but for now the customer paid with credit card and we will follow up shortly.

Arrived on site met with customer, turn system on attached gauges outside and found system to be low on charge. Removed cover from air handler and found some ice on the coil. Scheduled a comfort adviser for tomorrow July 29 9-10a. Static pressures R .04 S .66. Advised customer to leave system off to have air circulation in the home. Left Comfort club brochure with customer

Arrived to check 5 year old disposal not working with switch. Reset is not tripped and disposal is not locked up. Unplug from wall and put in bottom outlet and it is now working, plugged back into the top outlet and it is now working, informed customer it could be the switch is getting weak. Disposal is in good shape and working properly at this time.

System- Downstairs Approx Age of System: 17 Refrigerant Type- R22 Metering Device- TXV SP/HP: 66/190 SLT/LLT: 68/94 VSAT/LSAT- 38/97 Superheat/Subcool- 29/3 Outdoor Entering Air Temp- 86 Outdoor Fan FLA- 1.36 Compressor RLA/LRA- 11/95 Contactor Voltage- 239 Capacitor Rating- 59.3/7.3 of 60/7.3 Indoor Return Dry Bulb Temp- 70 Return Wet Bulb Temp- 63 Supply Temp- 48 Temperature Difference- 22 Required Difference- 15-22 Blower FLA- 5.8 Filter Sizes – 16x25x1 Changed Filters – N Blew out drain line: Y Returned tstat to original settings: Y Unit operational; prior to leaving: Y Notes- Performed AC tune up. This drain line for this system is tied together with the upstairs and was backed up. I cleared the drain lines as included with the tune up. Recommend installing safety switches to prevent water damage to the house from future issues with the drain line. Systems are older and showing heavy fatigue, may require replacement soon, at this time they are still

Found refrigerant leak in the evaporator coil. The house is sold with closing on Friday. I have a comfort advisor scheduled for this afternoon between 1-2 for pricing on evaporator coil change out. Statics R-0.21 FR-0.54 FS-0.31 SP-0.15

System- Single Approx Age of System: 14 Refrigerant Type- R22 Metering Device- TXV SP/HP: 68/196 SLT/LLT: 52/96 VSAT/LSAT- 39/99 Superheat/Subcool- 13/3 Outdoor Entering Air Temp- 86 Outdoor Fan FLA- 1.2 Compressor RLA/LRA- 9.2/89.1 Contactor Voltage- 242 Capacitor Rating-60/10 Indoor Return Dry Bulb Temp-72 Return Wet Bulb Temp- 55 Supply Temp- 49 Temperature Difference- 23 Required Difference-21 Blower FLA- 6.8 Filter Sizes – 20x30x1 Changed Filters – N (clean) Blew out drain line: Y Returned tstat to original settings: Y Unit operational; prior to leaving: Y Notes- performed ac tuneup. System was operational upon arrival. System operating good at this time. Hardstart kit installed, run capacitor is a new turbo200X. Blowout valve and emergency pan switch installed. Recommended installation of an in-line float switch.

RTU1 Trane MN: YHD180G4RLA00H0C1A1A000A SN: 151410806D Cleaned the algae from the bottom of the evaporator coil. I used my high pressure tip on the water hose to force the water through and get the algae off. Then ran water over the coil to make sure the coil was draining correctly. Unit looks to be draining correctly at this time.

AC Diagnostic System: Refrigerant Type R22 Metering Device-Fixed Orifice SP/HP: 70/274 SLT/LLT: 65/105 VSAT/LSAT: 41/124 SH/SC: 24/19 Outdoor Entering Air Temperature 81 Filter Size(s) 16x25x1 Returned tstat to original settings: Yes Unit operational; prior to leaving: Yes Notes: Customer stated unit froze up on them this weekend. They noticed the evaporator coil was dirty so they cleaned coil to get airflow through it. I checked pressures and the pressures look fine. The system is original to the house (95). I would begin budgeting for a new system due to the age of the equipment. At this time cooling has been restored.

Came out today to see what was leaking on one of the customers faucets that we put in. After running the sink for a while filling up the drain and releasing it numerous times we also took the handles off one by one and finally lifted the body of the Faucet off the counter and realized the faucet had a super slow internal leak that was eventually dripping below. The customer had mentioned that she saw water coming out of the front of the Faucet so we got on the phone with Moore supply and got it set up for her to exchange the defective Fixture. While we were there we checked the other two Fossetts and serviced the handheld sprayer to get it to flow better by cleaning it out. Customer will let us know when they get the top half back in so we can come by and put it on and also pick up my battery and charger that was left behind that the contractor picked up.

Arrived on site met with customer then went upstairs to the water heater was at had to turn off water at the street then drain down water heater and take out . Installed new water heater and ball valve gas flex and water flex .take old heater downstairs for hall off picked up and clean work area.turn on water to the house checked for leaks no leaks at this time then light water heater job is complete.

Customer stated the only warm air would blow in the home so it went to condenser. Found wire from the contactor burnt off the capacitor capacitor also failed but wire from the contactor was still alive and was hitting the condenser the whole time it was on turn the power off at the breaker so no more electrical burning can happen to the condenser. Total customer That it would be better to replace due to the age and issues happening in last tuneup I told them that this could happen to the unit and it is now showing up. If customers did not want to replace let them know we would have to redo the electrical for the condenser but could not promise that nothing else in the system took damage. Husband said that they will leave it as is for now now and see what they want to do. Customer would like the office to run the $49 service fee.

AC Diagnostic System: upstairs Returned tstat to original settings: Y Unit operational; prior to leaving: Y Notes: Water found in emergency drain pan, not enough to trip the pan float switch, recommended installing a blowout valve and flushing drain line to restore proper flow. Also recommended replacing drain pan due to the amount of rust. Recommendations: AC Diagnostic System: downstairs Returned tstat to original settings: Y Unit operational; prior to leaving: Y Notes: organic growth found in supply plenum, recommend installing an air scrubber to kill of organic growth, help prevent further buildup and increase air quality. Also recommended replacing drain pan due to amount of rust. Did recommend comfort club membership, customer will wait at this time, is going to think about drain pan replacements. Recommendations: Air Scrubber Blowout Valve Drain Pan

System- upstairs Approx Age of System: 6 Refrigerant Type- R410a Metering Device- TXV SP/HP: 132/281 SLT/LLT: 68/92 VSAT/LSAT- 46/92 Superheat/Subcool- 21/5 Outdoor Entering Air Temp- 81 Outdoor Fan FLA- 1.20 Compressor RLA/LRA- 10.98/110 Contactor Voltage- 243/24 Capacitor Rating- 46/10 Indoor Return Dry Bulb Temp- 75 Return Wet Bulb Temp- 65 Supply Temp- 60 Temperature Difference- 15 Required Difference- 15-20 Blower FLA- 5.40 Filter Sizes – 20x25x4 Changed Filters – Clean Blew out drain line: N (no access) Returned tstat to original settings: Y Unit operational; prior to leaving: Y System- downstairs Approx Age of System: 6 Refrigerant Type- R410a Metering Device- TXV SP/HP: 112/296 SLT/LLT: 69/96 VSAT/LSAT- 37/95.6 Superheat/Subcool- 28/6 Outdoor Entering Air Temp- 81 Outdoor Fan FLA- 1.17 Compressor RLA/LRA- 14.70 Contactor Voltage- 243/24 Capacitor Rating- 77/10 Indoor Return Dry Bulb Temp- 73 Return Wet Bulb Temp- 63 Supply Temp-

Came out today to finish the master shower by trimming out the handheld/bar. Shower is complete but while we were there the customer had us go ahead and change out the top half of four faucets in the house. The customer also had her tile repaired and the sheet rock repaired from our last visit and the price of this visit was $220 so we didn’t charge for today but will credit or charge accordingly when the customer sends us the bill for the tile and sheet rock repair that was made. Customer will let us know when she gets the invoice and forward it over to us so we can square it away. No follow up at this time.

AC Diagnostic System: zone Refrigerant Type R410A Metering Device-TXV SP/HP 136/296 SLT/LLT 58/96 VSAT/LSAT44/107 SH/SC17/6 Outdoor Entering Air Temperature 97 Filter Size(s)20x25x4 Returned tstat to original settings: Y Unit operational; prior to leaving: Y Notes: customer stated that the home was cooling but the casita was hot set at 75 and it was 85 int there. Went up to attic and found damper stuck closed for casita. Also noticed that ductwork has organic growth around the plenum. Since unit is 8 years old and she has had so much trouble with her unit and it being a 3 zone unit I recommended A comfort advisor so we can get her better equipment for her home with the zones. Customer said she knows that’s the better idea but for now she would like the damper motor fixed and a air scrubber to prevent any from building up inside the plenum. Installed new damper and made sure it opened when called for and installed air scrubber. Casita is getting air flow into the room now and un

System- 1 Approx Age of System: 7 Refrigerant Type- R410a Metering Device- TXV SP/HP: 131/341 SLT/LLT: 64/98.8 VSAT/LSAT- 45/104 Superheat/Subcool- 17/7 Outdoor Entering Air Temp- 90 Outdoor Fan FLA- 1.32 Compressor RLA/LRA- 12.33/90 Contactor Voltage- 242/24 Capacitor Rating- 45/7.5 Indoor Return Dry Bulb Temp- 78 Return Wet Bulb Temp- 67 Supply Temp- 61 Temperature Difference- 17 Required Difference- 15-20 Blower FLA- 5.45 Filter Sizes – (3) 12x12x1-16x25x1 (2)-12x24x1 Changed Filters – Y Blew out drain line: Y Returned tstat to original settings: Y Unit operational; prior to leaving: Y Notes- checked indoor unit for proper operations. Unit has reme halo working properly, complete overflow protection. Proper temperature splits and amp draws, evaporator coil is slightly dirty has never been cleaned will recommend evaporator coil cleaning, checked outdoor unit for proper operations, turbo200 and hardstart kit working properly refrigerant pressures and elect